Ways To Remove Additional Slats From Wood Blinds
Stunning wood blinds are the stylish addition to home decoration and offer functional advantages at the same time. However due to constant use for a long period of time, these items are easily damaged. Replacing the damaged blinds with the new ones cost you a lot of money. The best option is hire a professional for wood blind repair Utah and maintenance. If you are using lengthy blinds and you would want to cut the size, then you should remove the additional slats from these blinds. For this task you have follow simple tools. Here are a few tips that you can follow for repairing these items.
Lower the window blinds fully
The first step is to lower wood window blinds with the help of pull strings. Then you should open the item by using title want. Make sure that the slats are widely separated from one another. Use the masking tape on a slat that is even with sill of the window. It will be used as a new slat at the bottom. Turn upside the bottom bar of these blinds and gain access to the plugs of the string. You might have five to six plugs on the basis of the breadth of these items.
Put the plugs with help of screwdriver
The next step is to pry all the plugs from the slat at the bottom with the help of a flat screwdriver. You should use scissors to cut down the string attached to plug and remove the additional part of the string from plugs. For wood blind repairing and installing, you should set these plugs inside a safe area. Remove the bar at the bottom from the strings as well as keep them away from window blinds. You should set the bar aside.
Measure the slat
Use a masking tape to measure the area of the slat up to six inches. You should then cut the strings at this six inch mark across the breadth of these wood window blinds. Then the slats can release from the area where you have cut down the strings. However you have to leave intact slats below the new slat at the bottom. These lift cords become the center strings that pass through these holes in the slat. The ladder cords are the special cords that run alongside the front as well as back side of the slats with tiny piece under the slat.
Pull down the ladder cords
You have to pull down the ladder cords below the bar of the bottom. Then you have to cut down these cords below the second set of the ladder beneath the bar of the bottom. You should cut down the cords of the connector on both the ladder sets below bottom rail. These connector cords are the special cords that are used to place the slats in the cord of the ladder.
Tie the knots effectively
Another vital step of wood blind repairing is to tie the knots at the end of the ladder cord. Then you have to twist the cords together as well as insert them through the holes inside the bottom bar from the top side through bottom side. The ladder cords are placed inside the notches on the plug as well as push these plugs into these holes inside the bottom bar. It secures the strings and the blinds are shortened.
Lower the window blinds fully
The first step is to lower wood window blinds with the help of pull strings. Then you should open the item by using title want. Make sure that the slats are widely separated from one another. Use the masking tape on a slat that is even with sill of the window. It will be used as a new slat at the bottom. Turn upside the bottom bar of these blinds and gain access to the plugs of the string. You might have five to six plugs on the basis of the breadth of these items.
Put the plugs with help of screwdriver
The next step is to pry all the plugs from the slat at the bottom with the help of a flat screwdriver. You should use scissors to cut down the string attached to plug and remove the additional part of the string from plugs. For wood blind repairing and installing, you should set these plugs inside a safe area. Remove the bar at the bottom from the strings as well as keep them away from window blinds. You should set the bar aside.
Measure the slat
Use a masking tape to measure the area of the slat up to six inches. You should then cut the strings at this six inch mark across the breadth of these wood window blinds. Then the slats can release from the area where you have cut down the strings. However you have to leave intact slats below the new slat at the bottom. These lift cords become the center strings that pass through these holes in the slat. The ladder cords are the special cords that run alongside the front as well as back side of the slats with tiny piece under the slat.
Pull down the ladder cords
You have to pull down the ladder cords below the bar of the bottom. Then you have to cut down these cords below the second set of the ladder beneath the bar of the bottom. You should cut down the cords of the connector on both the ladder sets below bottom rail. These connector cords are the special cords that are used to place the slats in the cord of the ladder.
Tie the knots effectively
Another vital step of wood blind repairing is to tie the knots at the end of the ladder cord. Then you have to twist the cords together as well as insert them through the holes inside the bottom bar from the top side through bottom side. The ladder cords are placed inside the notches on the plug as well as push these plugs into these holes inside the bottom bar. It secures the strings and the blinds are shortened.
Source...